Getting Stable Steering from a Jeep Wrangler

Stabilizing a Jeep's coil spring/control arm suspension is not easy but well worth it when you get it right.

Sep. 13, 2017 By Jim Brightly
Maneuvering over and around boulders such as these requires strong systems—both steering and suspension.

If you are a mall crawler, a Jeeper who never takes your Jeep to the rocks, wash-outs, and shale hills that make for exciting wheeling; you need not read any further. Your Jeep's steering and suspension systems are more than stout enough to last for as long as you own the Jeep.

However, if you're more like me and use your Jeep on adventures for which it was designed, read on.

The components in the following article are available for all TJ/LJ/JK model Jeeps; just slightly modified with different part numbers for the various models. However, the installation procedures will be very similar.

To paraphrase the old motorcycle rider's axiom, there are two kinds of Jeep drivers: Those who have experienced death wobble (DW) and those who will experience death wobble. Well, if your Jeep has leaf springs, you'll probably never experience DW. It only seems to affect those with coil spring and control arm suspensions. In order to avoid DW, you first must maintain the steering and suspension system very well. Keep everything well greased and tight.

Before we get into the changes, let's mention that this Jeep - a 2005 Rubicon Unlimited - is equipped with a TNT Customs long-arm 4” lift kit with ARB springs and Fox shocks. This is one of the best hardware kits I've ever worked with. Its axle trusses, which are used for control arm connections to the differentials, greatly strengthen the stock Dana 44 differentials, but must be precisely located.

Oversize tires (such as these Yokohama Geolandar M/T G003 12.50x37R17) can wear out tie rod ends much more quickly than stock tires, and the stresses of rock crawling will accelerate the wear even more quickly.

Now, with the TNT long-arm kit installed, the first thing to do is strengthen the Jeep's steering. We discarded the OEM drag link and tie rod for a new assembly from Rugged Ridge. It's the Tie Rod and Drag Link Kit (SKU: 18050.82, $386). According to the company's literature: This is a bolt-on solution for preventing bent tie rods from wheeling with larger tires; the tubes are 1-1/4 inch OD steel that is cold rolled, pierced, and drawn through dies to produce a ¼-in. wall thickness. You get one-ton strength without any modifications to your steering knuckles. The manufacturer also says that vehicles with less than two inches of lift but more than four should not be outfitted.

New Rugged Ridge heavy-duty tie rods can control large tires on lifted Jeeps much better than OEM units. And don't forget to include a steering stabilizer.

Once we had the steering under control, we wanted to add more travel to the suspension so dirt roads could be handled at higher speeds without damaging any components. The TeraFlex TJ SpeedBump bump stops are a composite system designed for high-performance Wrangler applications. Bump stops reduce suspension compressing impacts and the associated harsh bottoming out. This action reduces the risk of bending an axle housing and increases the ability to maintain vehicle control.

Limiting straps—these are from Skyjacker—limit suspension droop and keep your coil springs where they belong.

The company says, "TeraFlex SpeedBumps feature performance tuned closed-cell nitrogen charged microcellular polyurethane technology, providing a true progressive bump stop that will not fade or dissipate under extended heavy use. Microcellular polyurethane technology is not affected by temperature extremes, and retains thermal and sub-zero temperature flexibility. The Delrin acetal resin polymer shaft is self-lubricating to allow thousands of continuous cycles without wear or abrasion."

In order to install the Terra Flex bump stops, we had to enlarge the hole in the spring tower.

After adjusting the bump stop's height to the Jeep's requirements, we reassembled everything.

Use the Terra Flex mount itself as the locating template.

Weld the mount into place.

Reassemble all the suspension components.

So, with the SpeedBumps in place, the suspension works in this manner. The Fox shock absorbers control compression and rebound over the light-duty surfaces where the springs don't compress all that much. When things get frisky and the springs begin compression more, the SpeedBumps come to the assistance of the Fox shocks. The coupling of the bump stops with shocks keep both bump stops and shocks from working as hard as they would singly, therefore producing less heat in each, extending the life and control of each component. A side benefit of adding the bump stop's mounts raised the Jeep at least another inch (we weren't expecting that so we didn't measure before and after).

Curry Antirock sway bars come in two kits. This is the front kit for the TJ/LJ models. Everything is included but the lower mounts (those are made to match the individual Jeeps).

The piece d'resistance that ties everything together is the Currie Antirock Sway Bars (front, CE9900, $396; rear, CE9900-TJR, $475). The Currie Antirock sway bar kits provide the balanced performance of front and rear suspension for rugged off-road conditions. They give the driver increased traction by balancing and distributing the weight over all four tires.

The full-width torsion bar utilizes the Jeep's front tubular cross member.

They're made of SAE 4130 heat-treated steel for ultimate strength. Unlike factory sway bars, Currie Antirock sway bars need not be disconnected when off road for more articulation. And like the OEM sway bars, they greatly reduce lean on highway curves and corners. On those narrow, slippery, off-camber trails, the Curry Antirock Sway Bars steady your Jeep and your nerves.

Depending on how much your Jeep has been used, you may have to clean up the crossmember's ends before installing the neoprene bushings.

You may still have to use a large hammer or hand sledge to fully seat the bushings.

Carefully drive the torsion bar into place. Make sure you don’t knock out the opposite bushing while seating the torsion bar.

Slide the control arm over the torsion bar and tighten both the end bolt and the clamp bolt.

Use heavy construction paper or cardboard to make a template for the lower mounts. Cut from at least ¼-inch steel plate. Modify it until it fits perfectly and then weld into place. Weld both sides so that it can withstand the stresses that will be put upon it.

This is Curry's rear kit.

The kit mounts to the Jeep's frame rail behind the rear differential.

Depending on what you’ve added to your Jeep, you may have to modify the mounting location.

Everything's in place. You can determine which hole to use in the control arm by how stiff you wish the sway bar to be. Bolt it nearer the torsion bar to soften its effect; nearer the end to stiffen it.

One last thing, make sure your shock absorbers are doing their job. In the old days, we'd simply push a car's bumper down sharply and allow it to rebound quickly. If it steadied with just the one rebound, the shocks were good. With your Jeep's shocks being much better designed and much stronger, a little more work is involved testing them.

One last thing. If your shocks are good—see text for testing them—make sure your tires are spin balanced.

It's not very scientific but it seems to work. Using a floor jack, lift the Jeep with one differential at a time to where the tires are 6 to 8 inches off the ground. Release the floor jack quickly and completely so that the Jeep bounces on the ground. If, like the car above, the Jeep only bounces once, that differential's shocks are good. Do this at both ends, and then visually inspect all four shocks carefully. Make sure they don't scrape or contact any surface during their movements. Make sure they are not leaking (look for oily residue or dirt collecting on oil). Lastly, make sure their mounting bolts are tight and meet their torque specs.

With stable steering and suspension, rocky trails like this one can be much more fun.

Source: Summit Racing, Newsletter
Join our Weekly Newsletter to get the latest off-road news, reviews, events, and alerts!