D-I-Y Custom Snorkel - Trucks 4x4 @ Off-Road.com

HOME :: ABOUT US :: ADVERTISE :: RSS FEEDS :: SUBSCRIBE/eNEWS

Price and Compare Vehicles:
New, Used, and Powersports

D-I-Y Custom Snorkel

Publish date: Nov 1, 2005
By: Jeff Henderson
Source: Chevy at Off-Road.com

When it comes to deep water, the best insurance you can buy for yourself is an Snorkel. The fastest way to do extensive damage to your vehicle while crossing water is to hydro-lock the engine. With snorkel, you no longer have to wonder if the water level is up to your air intake. You know exactly how close the water is to your intake, because you can look out your windshield and see it! True, there are kits you can buy but none are made for the S-10 and the prices they're charging, you would think the kits are made of gold! Jeff decided to take a different approach at this and just make his own. Follow the steps below and you will see how easy this is to make yourself.

Parts:
Most everything you need you can get from your local hardware store. The parts you need are:

4-3" PVC right angle with out a lip on one end
2-3" PVC right angle with a lip on one end
1-3" PVC 45 angle
6 Feet of 3" ABS pipe (Like PVC but cheaper and weaker)
4" air hose for a air cleaner (Like dryer vent hose but stronger) Get this from
local auto parts place
PVC pipe glue and the purple sealer
2 cans of flat black or bumper trim black spay paint
A tube of Black caulk

Tools that you will need:

A body mans cut off wheel
Caulk gun
Drill
1/8 drill bit
metal file
Chop saw
1/8 metal screws

Installation:

Your first step is to cut a hole in the fender. If you don't want to do this stop now since this is required. I used a body mans cut off wheel to do mine. Here is the outside view of the hole. The window washer bottle needs to be moved forward. Make sure that the hood will close before you mount it.

Here's the inside view of the hole.

Here's the PVC glue and sealer that is used to hold the pipes together. The purple sealer is also a cleaner for the glue and helps it bond.

Before you glue everything together, you should label everything at the joints. As you can see how I wrote TOP across the two joints so I know where it should line up when it comes time to glue it together. This is the Top piece that has the lip cut off and the 45-deegree piece under it.

This is were I made a piece to but the joints together. I cut a 3" long piece of tube that will fit between the two pieces. It will allow them to but right up to eachother for a nice fit.

Using a chop saw, I had to cut two 45-deegree angles for the pipe the runs across the windshield. It needs to be 18"long from the point of the angle cut. I used the wood blade that was in the saw and it seem work nice on cutting the ABS pipe. The other piece needs to 5&1/2" long. That is the piece that runs across the cowl.

The breather on the air cleaner that gets hot air from the exhaust manifold well need to be tack welded shut and sealed with caulk.

To make the snorkel hose, it needs to be attached it to the air cleaner housing. Cut a 5" long piece of ABS and push and it over the housing. Drill a 1/8" hole through the ABS pipe and the housing. Screw it into place.

After you have the ABS screwed into place you need to seal it. Seal all the way around the pipe and the housing. You also need to seal around actuator for the hot air intake as well. Use the caulk (RTV silicone) to do this.

Now you're ready to glue the two 45-degree cuts together that you made a while ago. Use the PVC pipe purple sealer and glue right on the cuts. Press together by hand and hold firmly until it stays. Let it dry for 20 minutes. I took a small hinge about an inch long, cut the ears off of it, and screwed it over the joints to help it stay together.

After you get all the joints lined up and marked, install it on the truck to so you know the cuts are correct. Before it's glued together you need to wipe all pieces with a mild paint thinner. Be careful the paint thinner will eat the pipe so don't soak it. Next, you will need to sand it down with a piece of gray scotch-brite so the paint will adhere on the plastic. Before you paint use the caulk to seal the joints so there's no air leaks.

All painted and ready to go on the truck.

If you have a TBI set up on your truck you'll need to seal up the 4 wires that run to the injectors. You also want to make sure that the gasket beween the TBI/carb seals correctly and is good.

The distributer cap should be sealed with the caulk as well. I just sealed this one with red RTV so that you can see how to do it. Just run a small bead on the inside of the cap. Because the cap needs to vent and now you are sealing it off you will have to replace it just about every time you change your oil. If you don't you will get carbon build up on the terminals. Another solution to this is drill a small hole in the top and find a small rubber plug to fit the hole when you take it off-road.

All your axle vent tubes should be re-routed under the hood. The best place I found is right by the firewall.

Most of the plugs on the truck are sealed fairly good. You may want put a dab a sealant where the wires route in the back of the plug.

The tranny and oil dipsticks can be sealed with a piece of duct tape. If you own a 4.3L you can buy dipsticks that lock down and seal.

This is how the air hose should run under the hood. This can be difficult to hook up. I cut the top snorkel piece off (the lip) and slid it over the piece that went through the fender. Then the lip that you cut off you glue a piece of ABS pipe about 4" long which is what you attach the air hose to.

This is how it should look after it's finished. The air cleaner lid has a rubber gasket that has a good seal.

This is the mount for the top. It's a loop clip that I screwed into the inside of the door pillar and the fender. Zip ties were used to hook it to the snorkel.

This is the front view of the snorkel on the truck. You need to move the wiper down a little so that it dosn't hit the snorkel.

How the hole set up will look on the truck. Now... where's some water...

This completes the installation. Now that it's waterproofed, you're ready to go snorkeling! Don't forget your swim shorts!

Questions about this page should be directed to: chevy@off-road.com.

We cannot guarantee a response to every letter we receive.

Back to the Chevy WebPages

Comments from our Readers

reeves_mck / la luz, NM, UNITED STATES
Posted Feb 18 2008 09:56PM
If your driving in the rain or water splashes up wont it go straight into your intake? have you had this problem?

About the Author

Jeff Henderson

Articles by Jeff Henderson

Untitled Document

Sponsored Links

HOLY CRAP Or Your Money Back -
Once you try it - we dare you to drive without it. To learn more click here.

Off-Road Videos -
Check out over ten years of extreme 4x4 action, product testing and the Off Road Nation at play. Baja racing to rock crawling, ATVs in the sand to motorcycles in the dirt, it's all here. Rate them, share them and upload your own.

ATV Reviews -
Honda, Suzuki, Yamaha, Polaris, Kawasaki, Can-Am. First rides to long-term tests, check out the latest in ATVs, UTVs and Side-by-Side vehicles of every make and model. Read expert opinions and follow custom project vehicles.

Own your very own Off Road Superstore.....
How many times have you pondered the idea of owning your very own off road shop? Let the staff at Off Road Innovations, one of the largest aftermarket off road accessory dealers in the US, help turn your hobby into a profitable career. Go to www.offroadinc.net for more info or just call 800-809-6088.

MSD Ignition Rebate!
Fire up with MSD Ignition and receive Cash for Cruising! Click on the link to find out the latest cash back rebate from MSD.

More On Trucks & 4x4

All 4x4 Features 4x4 Forums 4x4 News 4x4 Reviews 4x4 Video 4x4 Voices

Chevy Dodge Ford Hummer Nissan Suzuki Toyota

Sell Your 4x4 Buy a New 4x4 Parts for Your 4x4

Off-Road Video

Enewsletters

Stay on Top of All the Action:
Sign up for Off-Road.com's Enewsletters